开裂简支梁动力特性的两种解析方法对比研究
DOI:
作者:
作者单位:

taptap点点官方注册

作者简介:

通讯作者:

中图分类号:

基金项目:

基于元胞自动机重载交通流-损伤梁桥耦合随机振动模型研究


Comparative Study on Two Analytical Methods for Dynamic Characteristics of Cracked Simply Supported Beams
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    准确高效地计算带裂缝桥梁结构动力特性,是开展桥梁结构损伤识别和状态评估等研究工作的重要前提。本文基于裂缝局部柔度模型,研究带裂缝简支梁动力特性两种解析求解方法的优势。根据传递矩阵法和分段振型函数法基本思想,采用无质量扭转弹簧模拟裂缝引起的局部柔度,分别借助递推方法和Heaviside 函数,推导了带任意数量裂缝简支梁动力特性的两种求解方法,并与ANSYS有限元结果对比分析,探讨了两种方法在计算精度和计算效率上的异同点。结果表明:无论是单裂缝、双裂缝、三裂缝梁,两种方法计算结果与有限元结果吻合较好,均具有较高的计算精度;与传递矩阵法相比,分段振型函数法在计算多裂缝梁固有频率时具有更高的计算效率,尤其是对于高阶频率,三裂缝下最大计算时间差值为16.51s;裂缝数量增加,传递矩阵法固有频率计算时间分别增大2.85倍、13.3倍,分段振型函数法分别增大1.1倍、5.43倍,传递矩阵法计算时间显著增加且呈指数增长趋势;裂缝深度的变化对计算效率的影响较小。分段振型函数法计算多裂缝简支梁高阶频率特性,具有明显的优势。

    Abstract:

    Accurately and efficiently calculating the dynamic characteristics of bridge structures with cracks is an important prerequisite for conducting research on damage identification and condition assessment of bridge structures. Based on the local flexibility model of cracks, this paper studies the advantages of two analytical methods for calculating the dynamic characteristics of simply supported beams with cracks. According to the basic ideas of the transfer matrix method and the segmented mode function method, a massless torsional spring is used to simulate the local flexibility caused by cracks. Two methods for calculating the dynamic characteristics of simply supported beams with arbitrary number of cracks are derived by means of recurrence method and Heaviside function respectively. The results are compared with the finite element results of ANSYS, and the similarities and differences in computational accuracy and efficiency of the two methods are discussed.The results show that both methods have good agreement with the finite element results, and both have high computational accuracy. Compared with the transfer matrix method, the segmented mode function method has higher computational efficiency in calculating the natural frequencies of multi-crack beams, especially for high-order frequencies. The maximum calculation time difference for three cracks is 16.51s. As the number of cracks increases, the calculation time of the transfer matrix method increases by 2.85 times and 13.3 times respectively, while the segmented mode function method increases by 1.1 times and 5.43 times respectively. The calculation time of the transfer matrix method increases significantly and shows an exponential growth trend. The change in crack depth has a small impact on computational efficiency. The segmented mode function method has obvious advantages for calculating the high-order frequency characteristics of simply supported beams with multiple cracks.

    参考文献
    相似文献
    引证文献
引用本文
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2024-03-09
  • 最后修改日期:2024-05-09
  • 录用日期:2024-05-11
  • 在线发布日期:
  • 出版日期:
Baidu
map
关闭